ATRIP · Western blot design guide

ATRIP Western Blot Planning Guide

Plan an ATRIP Western blot around the catalog-observed 85.8 kDa band, image-backed A03862-2 evidence, HPA controls, and verified protocol records.

Evidence assembled July 2026 · For research use; verify linked source records and product datasheet before use
Western blot protocol sheet for ATRIP (ATRIP): expected band 85.8 kDa, antibody A03862-2, and guide-derived SDS-PAGE protocol steps
ATRIP Western blot protocol sheet — expected band 85.8 kDa, antibody A03862-2, controls and PMC citations. Open the full ATRIP WB guide →

ATRIP Western Blot Experimental Design Guide

Expected bands, documented protocol parameters, controls and antibodies — the at-a-glance facts below, then the full design guide.

Must know before running
Expected band 85.8 kDa
Observed band Not reported — verify product WB image
Gel 8-10%
Positive control ⓘ Cerebellum
Negative control ⓘ Adipose tissue
Important caveats
Reasons your observed band may differ from the expected size.
ⓘ Calculated mass 85.8 kDa
ⓘ Localization Nucleus
ⓘ Processing / PTM Record-dependent
ⓘ Reactivity Human / Mouse / Rat
Section 1

Real Curated ATRIP Western Blot Protocols

Start with the molecular-weight rule, then compare verified publication-derived conditions.

Recommended Western blot protocol parameters
Sample / lysateAppendix
Gel %8-10%
Load20-30 µg total protein per lane
TransferSemi-dry, standard transfer
Membrane0.45 µm PVDF
Blocking5% non-fat milk or 5% BSA in TBST
PrimaryA03862-2 at datasheet starting dilution
Primary incubationOvernight at 4 °C with gentle agitation
SecondarySpecies-matched HRP conjugate at validated dilution
Wash3 × 5 min in TBST
DetectionChemiluminescent substrate
ExposureBracket exposures to avoid saturation
Section 2

What Is the Expected ATRIP Western Blot Band Size?

Use the product-observed 85.8 kDa band as the primary planning value and retain the UniProt calculated mass as context.

What am I looking at on my blot?
85.8 kDaMatches the authoritative product WB observation.
85.8 kDa calculatedUse as UniProt context, not as a replacement observed band.
Unexpected additional signalDo not assign identity without orthogonal positive/negative controls.
💡Expected ATRIP appearancePlan around 85.8 kDa and keep the calculated mass as supporting context.
How each factor affects band size
Catalog-observed band85.8 kDa; use this as the primary experimental expectation.
Calculated mass85.8 kDa from UniProt Q8WXE1; retain as context.
Gel selection8-10%; shared with the recommended protocol and poster.
Specificity checkCompare the lead HPA positive and negative controls with A03862-2.
Why is my band missing or off?
SituationLikely causeNext action
85.8 kDaMatches the authoritative product WB observation.Confirm with orthogonal controls and the linked product record.
Additional bandMay reflect processing, modification, or non-specific signal.Run a dilution series and compare positive/negative controls.
Weak signalTarget abundance or transfer may be limiting.Verify transfer, increase positive-control abundance, and bracket exposure.

Sample controls for ATRIP Western blot

🧪Use Cerebellum as the first positive-control candidate and Adipose tissue as the HPA Not detected negative candidate.
Positive control: Cerebellum (High)
Negative control: Adipose tissue (Not detected)
HPA protein score determines control status; other expression data is supporting context only.

HPA tissue expression evidence for ATRIP

Comprehensive Human Protein Atlas IHC scoring per tissue. Rows are taken directly from the HPA tissue chart — click any row's HPA link to view the source.

Positive expression · recommended positive controls

TissueCell typeLevelEvidenceSource
Cerebellum Reported tissue cells High Protein (HPA) HPA →
Cervix Reported tissue cells High Protein (HPA) HPA →
Caudate Reported tissue cells High Protein (HPA) HPA →
Appendix Reported tissue cells High Protein (HPA) HPA →

Undetected expression · recommended negative controls

TissueCell typeLevelEvidenceSource
Adipose tissue Reported tissue cells Not detected Protein (HPA) HPA →
Section 3

Advanced ATRIP Western Blot Tips

Deeper troubleshooting and optimisation questions for ATRIP, answered from its protein features.

Which band should guide the blot?
Use 85.8 kDa, the observation attached to the authoritative A03862-2 WB record.
How should calculated mass be interpreted?
Treat the UniProt calculated mass as context; it does not replace the catalog-observed 85.8 kDa expectation.
Which positive control should I start with?
Start with Cerebellum, the lead HPA protein-expression candidate.
Which negative control is defensible?
Use Adipose tissue as an orthogonal HPA Not detected candidate.
Which gel should I use?
Use 8-10% consistently across the quick facts, protocol table, and poster.
What transfer method to use for ATRIP Western blot?
Use the transfer method in the recommended protocol and verify transfer before blocking.
How should A03862-2 be started?
Start at the linked datasheet condition and run a three-point primary-antibody dilution test.
Which publication-derived protocols can I compare?
No verified publication protocol was supplied; use only the deterministic recommended protocol.
Boster reagents

ATRIP Western Blot Reagents

Human/Mouse/Rat-reactive ATRIP Western blot reagents with authoritative product imagery.

Real WB data Western blot validation image for ATRIP using A03862-2; observed band 85.8 kDa
Anti-ATRIP Antibody Picoband®
Cat # A03862-2

Only image-backed, WB-validated Human/Mouse/Rat recommendations from the prepared catalog evidence are shown.

Source: prepared picoband-wb product evidence; each card retains its own SKU, URL, observed band, and authoritative WB image.

References

  1. UniProt Q8WXE1
  2. Human Protein Atlas — ATRIP
  3. A03862-2 product record
  4. PMC2728292 — Cyclin-dependent kinase 2 dependent phosphorylation of ATRIP regulates the G2-M checkpoint response to DNA damage (Cancer research, 2007)