CR1 Western Blot Experimental Design Guide

Expected bands, validated protocols, controls and antibodies — the at-a-glance facts below, then the full design guide.

Must know before running
Expected band 223.7 kDa
Observed band Not reported — verify product WB image
Gel 4-12% gradient
Positive control Spleen
Negative control Bronchus
Important caveats
Reasons your observed band may differ from the expected size.
Calculated mass223.7 kDa
LocalizationMembrane
Processing / PTMRecord-dependent
ReactivityHuman

Sample controls for CR1 Western blot

🧪Use Spleen as the first positive-control candidate and Bronchus as the HPA Not detected negative candidate.
Positive control: Spleen (Medium)
Negative control: Bronchus (Not detected)
HPA protein score determines control status; other expression data is supporting context only.

HPA tissue expression evidence for CR1

Comprehensive Human Protein Atlas IHC scoring per tissue. Rows are taken directly from the HPA tissue chart on each tissue page — click any row's HPA link to view the source.

Positive expression · recommended positive controls

Tissue Cell type Level Evidence Source
Spleen Reported tissue cells Medium Protein (HPA) HPA →
Kidney Reported tissue cells Medium Protein (HPA) HPA →
Appendix Reported tissue cells Medium Protein (HPA) HPA →
Bone marrow Reported tissue cells Medium Protein (HPA) HPA →

Undetected expression · recommended negative controls

Tissue Cell type Level Evidence Source
Bronchus Reported tissue cells Not detected Protein (HPA) HPA →
Caudate Reported tissue cells Not detected Protein (HPA) HPA →
Section 1

What Is the Expected CR1 Western Blot Band Size?

Use the product-observed 223.7 kDa band as the primary planning value and retain the UniProt calculated mass as context.

What am I looking at on my blot?
223.7 kDaMatches the authoritative product WB observation.
223.7 kDa calculatedUse as UniProt context, not as a replacement observed band.
Unexpected additional signalDo not assign identity without orthogonal positive/negative controls.
💡Expected CR1 appearancePlan around 223.7 kDa and keep the calculated mass as supporting context.
How each factor affects band size
Catalog-observed band223.7 kDa; use this as the primary experimental expectation.
Calculated mass223.7 kDa from UniProt P17927; retain as context.
Gel selection4-12% gradient; shared with the recommended protocol and poster.
Specificity checkCompare the lead HPA positive and negative controls with A01022-1.
Why is my band missing or off?
SituationLikely causeNext action
223.7 kDaMatches the authoritative product WB observation.Confirm with orthogonal controls and the linked product record.
Additional bandMay reflect processing, modification, or non-specific signal.Run a dilution series and compare positive/negative controls.
Weak signalTarget abundance or transfer may be limiting.Verify transfer, increase positive-control abundance, and bracket exposure.
Section 2

Real Curated CR1 Western Blot Protocols

Start with the molecular-weight rule, then compare verified publication-derived conditions.

Recommended Western blot protocol parameters
Sample / lysateAppendix
Gel %4-12% gradient
Load20-30 µg total protein per lane
TransferWet/tank, extended transfer
Membrane0.45 µm PVDF
Blocking5% non-fat milk or 5% BSA in TBST
PrimaryA01022-1 at datasheet starting dilution
Primary incubationOvernight at 4 °C with gentle agitation
SecondarySpecies-matched HRP conjugate at validated dilution
Wash3 × 5 min in TBST
DetectionChemiluminescent substrate
ExposureBracket exposures to avoid saturation
Section 4

Advanced CR1 Western Blot Tips

Deeper troubleshooting and optimisation questions for CR1, answered from its protein features.

Which band should guide the blot?
Use 223.7 kDa, the observation attached to the authoritative A01022-1 WB record.
How should calculated mass be interpreted?
Treat the UniProt calculated mass as context; it does not replace the catalog-observed 223.7 kDa expectation.
Which positive control should I start with?
Start with Spleen, the lead HPA protein-expression candidate.
Which negative control is defensible?
Use Bronchus as an orthogonal HPA Not detected candidate.
Which gel should I use?
Use 4-12% gradient consistently across the quick facts, protocol table, and poster.
What transfer method to use for CR1 Western blot?
Use the transfer method in the recommended protocol and verify transfer before blocking.
How should A01022-1 be started?
Start at the linked datasheet condition and run a three-point primary-antibody dilution test.
Which publication-derived protocols can I compare?
Compare only the supplied target-verified records: PMC4833428, PMC6231989, PMC3265835.
Boster reagents

CR1 Western Blot Reagents

Human-reactive CR1 Western blot reagents with authoritative product imagery.

Real WB dataWestern blot validation image for CR1 using A01022-1; observed band 223.7 kDa
Anti-CD35/CR1 Antibody Picoband®
Cat # A01022-1
Reactivity: Human

Only image-backed, WB-validated Human/Mouse/Rat recommendations from the prepared catalog evidence are shown.

Source: prepared picoband-wb product evidence; each card retains its own SKU, URL, observed band, and authoritative WB image.